Fortis Roofing Farnborough 01252 596302 Get a quote

Gutters and fascias answer

Downpipe Replacement: When and Why

The downpipe is the part of the system that gets least attention. When it fails, the wall and the ground at its foot take the water instead.

The short answer

A downpipe needs replacing when it is cracked, split at a joint, pulled away from the wall, or blocked in a way that clearing will not cure. A single damaged length can often be swapped without renewing the whole run. The replacement should match the gutter's outlet, fit firmly to the wall and discharge somewhere the water can safely go.

Signs that a downpipe has failed

Watch the pipe during heavy rain. Water running down the wall beside it, spraying from a joint, or splashing out at a bend tells you where it is escaping. A dry day gives time to look more closely.

Cracks are the commonest fault in plastic pipes. Sun and frost make uPVC brittle, and a knock from a ladder, a ball or a lawn mower can split it, often along the seam. Cast iron and aluminium pipes fail differently: iron rusts through from the inside, while aluminium dents and pulls out of shape.

Joints leak when the pipe sections no longer push fully into each other, or when the seal or sealant has perished. A joint that was never fully engaged, or was left without allowance for movement, can open up as the pipe expands and contracts.

Fixings matter too. Pipe clips hold the pipe to the wall at intervals. If they have rusted, snapped or pulled out of the masonry, the pipe sags away, bends at the joints and leaks. A pipe that is visibly leaning needs attention before the weight of water in the next storm makes it worse.

Damp or green staining on the wall behind a pipe, a patch of wet ground at its base, or a puddle that does not drain are all clues that water is going somewhere it should not.

Blockages and when clearing is not enough

A downpipe carries a lot of water in a downpour, and it narrows at bends and shoes, the angled piece at the bottom. Leaves, moss, silt, and in older systems fragments of tile or mortar, build up and block it. Water then backs up into the gutter and overflows, often at the point where the outlet joins the pipe.

Clearing is the first step. A plumber's rod, a flexible cleaning tool or a jet from a hose can free a blockage from the top or bottom, working from a safe position. Take off the shoe or a bend if you can reach it, since debris tends to lodge there.

If the blockage returns, the pipe may be damaged inside. A crushed or kinked section, a joint with a ridge that traps debris or a pipe that has lost its fall at an offset can all hold material. Replacing that section solves a problem that cleaning only postpones.

A gutter that overflows with a clear pipe may have an undersized outlet, which is a design fault. BS EN 12056-3:2000 covers roof drainage design, and outlets and pipes should be sized to the roof they serve.

Our page on overflowing gutters explains how to tell a blocked pipe from an undersized system.

Materials and sections

Replacement pipes come in the same families as gutters. uPVC is the usual choice: light, cheap, in a range of fittings and simple to cut and join. It suits most modern houses and is the easiest to repair. Aluminium is stiffer and takes a factory finish, and is found on houses that want a metal look. Cast iron is traditional, durable if painted and maintained, and heavy, so it needs strong fixings.

Matching matters. A new section should suit the gutter outlet and the existing pipe's size and profile, round or square, and its colour. Mixing sizes or profiles gives ill-fitting joints and weak points.

A damaged length can often be replaced without renewing the whole run. The bad section is cut out and a new one is fitted with the right couplings, if the rest holds up and parts are to hand. Where the pipe is brittle, rusted or weathered throughout, replacing the whole run is the better buy, since the next length will fail soon after.

Where cast iron is involved, repair can be possible with careful work, and replacing like with like keeps the character of an older house. For a listed building or a conservation area, ask the council before changing the pipe's material or profile.

Fixings should suit the wall, with masonry fixings in brick and corrosion-resistant clips that hold the pipe clear of the surface.

Where the water goes, and what we do

A downpipe has to end somewhere sensible. In most cases it connects to a drain or a gully at ground level, through a shoe that directs the flow. Water discharged against a wall base, onto a path or into a flowerbed beside the house can soak the foundations and the wall, and cause damp.

Check that the gully or drain is clear and the connection is sound. A blocked gully backs up water around the foot of the pipe, and a cracked one leaks into the ground. Do not connect a pipe to a drain not meant for rainwater; if you are unsure, ask the council or the water company before changing the arrangement.

On the survey we run along each pipe, check the joints, clips and the shoe, look at the base and note the discharge. Photographs show each fault. A small repair, such as a new clip or coupling, is priced as such, and a full run is replaced only where the evidence supports it.

Access can be the cost driver, since pipes run the full height of the house. The total is quoted in writing, access included.

The gutters, soffits and fascias hub covers the whole system, and damp walls from a leaking gutter shows the damage a failed pipe can cause.

Downpipe faults and fixes

Can one cracked length of downpipe be replaced on its own?

Often yes, if the rest of the pipe is sound and matching parts are available. The damaged section is cut out and a new one fitted with the right couplings. Where the whole pipe is brittle or rusted, replacing the run is wiser, because the next length would fail soon after.

Why does my gutter overflow when the downpipe is clear?

The outlet or pipe may be too small for the roof area, the gutter may have lost its fall, or debris may be blocking the outlet itself. BS EN 12056-3 covers roof drainage design. A roofer checks the size, the fall and the outlet to find the actual cause.

Read next

Get your free roof quote

Get your free roof quote

Tell us about the roof and we will arrange a survey.

01252 596302

10-year workmanship guarantee, in writing.

WhatsApp us